Howto 2025-04-08 15:42:55

How to Unclog Drain Pipes Yourself

A clog in your kitchen or bathroom sink can often be remedied with some simple DIY solutions like a homemade snake or a combination of vinegar and baking soda. But when the blockage is rooted in your main drainage piping, the problem is a bit more complicated. Luckily, with a drain-cleaning machine rental and some safety precautions, you can unclog the pipes that run underneath your home and return your fixtures to normal operation.

Things You Should Know

Feed a bent clothes hanger into the drain, twist it, and pull it back out to quickly clear nearby clogs.
Or, mix equal parts of baking soda and salt, then add them to a pot of hot water. Pour the mixture down the drain and let it sit for 10-20 minutes, then turn on the tap.
Alternatively, set a wet/dry vacuum to its wet setting, and hold the nozzle over the drain. Turn on the vacuum and hold it over the drain until the clog clears.

Using Quick DIY Fixes

If the clog isn't too far down the pipe, a hanger might work! Find a wire coat hanger, straighten it out, and bend the tip to a 90-degree angle using a pair of pliers. The length of the hook should be small enough to fit through the drain. Push the hooked end down the drain and into the piping as far as you can. Afterward, twist it and pull it upward.

Repeat the above process until you pull something out.
If your drain has a basket strainer—the screen designed to catch foreign particles—remove it from below the sink with an adjustable wrench.
For a more effective solution, rent or purchase a plumbing snake that you can feed into the drain to clear out any clogs.

Mix ¹⁄₂ cup (120 mL) of baking soda with ¹⁄₂ cup (120 mL) of table salt. Stir the mixture with a spoon to ensure a consistent solution. Gently pour the mixture down the drain and let it sit in the piping for 10 to 20 minutes.

Flush the drain with hot water and see if the drain clears.

Start by pouring a pot of boiling water down the drain. Afterward, mix 1 cup (240 mL) of vinegar with 1 cup (240 mL) of boiling water. Throw ¹⁄₂ cup (120 mL) of baking soda into the drain and wash it down with your solution. Let the mixture bubble and sit for about 1 hour.
- Run hot water into the piping for 30 seconds after letting the mixture sit.
If you have a wet/dry vacuum, turn it to the wet setting and use the highest suction possible. Hold it over the drain to the clogged piping and wait for something to come up. Be sure to cover the vacuum vent using a plastic bag or container to catch any particles that make it through the filer.
- Don't try this method with a machine that isn't designed for wet work!
- If nothing comes out, try pressing the nozzle of the vacuum into the drain as far as possible.

Using a Drain-Cleaning Machine

If one fixture is clogged and the trap is not clogged, the drain line from that fixture is likely the culprit. For example, if your sink is not working but the trap is cleared, the drain downstream from the sink is probably clogged. If there are multiple clogs, the clogged pipe is likely downstream from where they connected.

Upper floor fixtures possess pipes that run under your home's flooring or downward to the basement. Look for floor drains to get a feel for where each pipe runs.

Either locate or estimate the location of the clog and measure the length from the clog to the cleanout plug. Head to a rental store and select a cable length long enough (ideally longer) to reach your clog.

For small drain lines that are 1.5 to 3 inches (3.8 to 7.6 cm) in diameter, select a cable ¹⁄₂ inch (1.3 cm) in diameter. For larger piping, select a cable ³⁄₄ inch (1.9 cm) in diameter.

Cleanout plugs are used to clean out your piping and are located in plumbing fixtures, leading away from your home, or in basement or garage floor drains. Regardless of where it is, have a bucket ready for the water that may drain out. Turn the square notch counterclockwise with your adjustable wrench. If you're having trouble, place a cold chisel to the corner of the square. Now, hit the handle with a hammer to get it going.

Never remove a cleanout plug or attempt to unclog a pipe that contains chemical drain cleaner.
Apply penetrating oil to the cleanout plug to loosen it up.
Wear leather gloves and safety glasses.

Connect the machine to either a grounded outlet or a 12- to 14-gauge grounded extension cord. Always keep the motor switch in the "Forward" position prior to turning it on. Be sure you aren't wearing loose clothing, jewelry, or belts, and put on safety glasses and heavy duty leather gloves.

Place the foot-operated switch somewhere easily accessible so you can step on it while feeding the cable into the drain.
Practice using the machine with the foot switch before trying to unclog the pipe.
Always follow the instructions given with the equipment—these are powerful machines.
Never wear cloth or rubber gloves—they can become caught between the coils of the drain-cleaning machine's cable.

Start by feeding the cable with the machine off until it doesn't go any further. Firmly hold the cable with both hands and start the machine's motor with the foot switch. Feed the cable into the pipe slowly while turning the motor on and off. Listen for the slowing of the motor and feel for an increase in the tension of the cable. Once you sense either change, stop immediately by taking your foot off the motor.

Never allow tension to build in your cable, which often happens when the cutting head hits an obstacle and stops turning.

After switching to "Reverse," hit the foot switch and watch the cable cage for 3 to 4 revolutions. This will decrease tension that accumulated in the cable after contacting the clog. Now, switch the motor to "Forward" again to continue chewing through the clog.

Proceed slowly and carefully to avoid the cable suddenly twisting around your arm.
Only use the "Reverse" motor option when the cable will not go forward or to relieve tension when removing the clog.

After you reach the clog, tighten the lock bolt located above the region the cable leaves the machine. While holding the cable and making sure the machine is running on "Forward," hit the foot switch. After it is depressed, loosen the lock bolt and wait for another 2 to 3 rotations of the cable. Now, retighten the lock bolt.